REFILL INK CARTRIDGES CANON BCI-60, BCI-61, BCI-62

Refill Ink Cartridge Canon BCI-60, BCI-61, BCI-62

Refill Ink

1. The filling holes are located under the label as shown. Just peel back the label leaving it still connected to the cartridge, do not remove completely.
2. Use the provided eyelet screw to widen the filling hole(s) in the top of the cartridge(s).
3. Connect the needle to the syringe and fill with ink.
4. Insert the needle into the widen filling hole. Note: This cartridge has a sponge so you may feel a slight pressure. Inject about 10 ml. of ink, per color until the ink bubbles up.
5. Pull the label back into place and use a piece of tape to hold it in place.
6. Rinse the syringe with water and dry between each color refill or store for future use.
7. Reinsert cartridge back into the printer and run 1 - 3 cleaning cycles as per printer instructions

REFILL INK CARTRIDGE BC-01, BC-02, BC-05, BX-02, BX-03, BC-06

Refill Ink Cartridge Canon BC-01, BC-02, BC-05, BX-02, BX-03, BC-06

Refill Ink

1. Use the eyelet screw to remove plug located on the top side of the cartridge. FOR BX-03 ONLY: A hole must be made on the top of the cartridge by using the hole making tool included in the kit. Firmly hold the handle of the tool and begin twisting the tool into the top corner of the cartridge. Continue twisting until it pierces the plastic cover. Once the plastic to is pierced, making the rest of the hole will go very quickly.
2. Connect the needle to the syringe and fill with ink.
3. Insert the syringe through the filling hole and push into the cartridge. Note: You may feel a slight pressure because the cartridge contains a sponge.
4. Inject up to 30 ml. of ink then reseal the cartridge with the plug that was re moved from step 1. FOR BX-03 ONLY: Use the plug provided in the kit to seal the cartridge.
5. Rinse the syringe with water and dry for future use, or use with a different color ink.
6. Reinsert the cartridge(s) and run a priming cycle as per printer instructions

REFILL INK CARTRIDGES CANON BJI-201BK HC, BJI-201BK, BJI-201C, BJI-201M, BJI-201Y

Reifll Ink Cartridge Canon BJI-201BK HC, BJI-201BK, BJI-201C, BJI-201M, BJI-201Y

1. With the cartridge upside down, using a screwdriver, push in the ball bearing that seals the filling hole. NOTE: There are several versions of these cartridges. One version has the filling hole under the label on the top of the cartridge. Another version does not have a ball bearing at all. In this case it would be necessary to make a hole for the needle to be inserted. Make this hole in the same spot where the ball bearing would be located, as shown below. Seal hole with the plug provided.
2. Connect the needle to the syringe and fill with ink.
3. Inject about 5 ml. of ink into the filling hole until the tank is full.
4. Use the included plug to seal the filling hole, make sure that the plug is sitting flush in the cartridge. Additional Note: If the cartridge has been empty/dry, the sponge will no longer accept any ink which will cause the cartridge to leak.
5. Rinse the syringe with water and dry for future use, or use with a different color ink.
6. Reinsert the cartridge and run a priming cycle as per printer instructions

APPLE COLOR LASERWRITER 12/600 PS AND 12/660 PS PRINTER SERVICE MANUAL

SERVICE MANUAL

The Color LaserWriter 12/660 PS is an enhanced version of the original Color LaserWriter 12/600 PS. The 12/660 engine and plastics are identical to the original in every respect, and all finished goods and service part numbers apply equally to both printers. The sole differences between the two versions are in the packaging and setup, the ROM and RAM on the I/O
controller board, and the driver software.

Packaging and Setup Changes The Color LaserWriter 12/660 PS requires two extra steps during setup, the leveling of the printer and the removal of oil absorption sheets from the fuser assembly.

Note : The orange flag that identifies the shipping screw has also been enlarged in the new version of the printer.

APPLE COLOR LASERWRITER 12/600 PS AND 12/660 PS PRINTER SERVICE MANUAL

Download
password : printer1.blogspot.com

REFILL INK CARTRIDGES CANON BCI-21 & BCI-24

REFILL INK CARTRIDGES CANON BCI-21 & BCI-24

Refill Instructions for inkjet cartridges Canon BCI-21 & BCI-24

1. Use a knife to remove the top of cartridge(s).
2. Use the included eyelet screw to enlarge the filling hole(s) in the top of the cartridge(s).
3. Connect the needle to the syringe and fill with ink.
4. Insert the syringe into the correct filling hole, (See diagram below for filling hole color) and push into the center of the cartridge. Note: You may feel a slight pressure because the cartridge contains a sponge.
5. Inject up to 5 ml. of ink, per color, into the cartridge.
6. Reposition the top and secure with a piece of tape.
7. Rinse the syringe with water and dry between each color filling or store for future use.
8. Reinsert the cartridge(s) and run a cleaning cycle as per printer instructions.

REFILL INK CARTRIDGES CANON BC-20 & BC-23

REFILL INK CARTRIDGES CANON BC-20 & BC-23

Refill Instructions for inkjet cartridges Canon BC-20 & BC-23

1. Use the eyelet screw to remove plug located on top of the cartridge.
2. Connect the needle to the syringe and fill with ink.
3. Insert the syringe through the filling hole and push into the cartridge. Note: You may feel a slight pressure because the cartridge contains a sponge.
4. Inject up to 30 ml. of ink then reseal the cartridge with the plug that was removed from step 1.
5. Rinse the syringe with water and dry for future use, or use with a different color ink.
6. Reinsert the cartridge(s) and run a priming cycle as per printer instructions

HP LASERJET 8000 / 8100 / 8150 SERVICE MODE

HP LASERJET 8000 / 8100 / 8150 SERVICE MODE

1. Hold down SELECT and JOB CANCEL while powering on the printer, until all lights are illuminated and the display is blank. If the display panel read INTERNAL TEST at this point, the keys were released too soon. Repeat this step until successful.
2. Press MENU, then SELECT. The message SERVICE MODE is displayed briefly, then the printer automatically begins an INTERNAL TEST. After several seconds, After several seconds, both control panel indicators turn off. The printer may display WARMING UP if it has not warmed up completely. After the printer has warmed up and passed the self test, SERVICE MODE is displayed.
3. Press MENU once to display SERVICE MENU.
4. Once it says SERVICE MENU press ITEM to scroll through service mode items.

To exit the service mode press GO.

LEXMARK OPTRA W810 RESET PRINTER METHOD

How to reset printer lexmark Optra W810

1. Enter the Configuration Menu by holding down the SELECT and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST. After the self test the display will read CONFIG MENU
2. Press the right arrow side of the MENU button until MAINT. COUNTER is displayed
3. Press the SELECT button, then scroll to RESET TRANSFER or RESET FUSER and press the SELECT button again to reset
4. Press the RETURN button to return to the Configuration Menu and press the left arrow side of the MENU button to exit the Configuration Menu.

RESETTER PRINTER LEXMARK

LEXMARK OPTRA SC1275 / COLOR 1200 RESET PRINTER METHOD

How to reset printer lexmark Optra SC1275 and Color 1200

1. Turn the printer off
2. Hold down the GO and RETURN keys while powering on the printer until PERFORMING SELF TEST is displayed
3. When REGISTRATION is displayed, press the right side of the MENU key six times until MAINTENANCE is displayed
4. Press the SELECT button, and then press the right side of the menu button to scroll to 80 or 81 RESET
5. Press the RETURN button until the display reads MAINTENANCE
6. Press the right side of the MENU button until the display reads EXIT DIAGNOSTICS
7. Press the SELECT button to return to the normal mode

RESETTER PRINTER LEXMARK

BROTHER MX-2001 / MX-2002 / MX-2003 LASER PRINTER SERVICE MANUAL

This service manual contains basic information required for after-sales service of the optional Mailbox unit, MX-2001/MX-2002/MX-2003 for the HL-2060 laser printer (hereinafter referred to as “this unit” or "the Mailbox unit"). This information is vital to the service technician to maintain the high performance of the unit.

This service manual covers the MX-2001 / MX-2002 / MX-2003 Mailbox units.

The service manual consists of the following chapters:

CHAPTER I : GENERAL
General view, specifications, etc.

CHAPTER II : THEORY OF OPERATION
Basic operation of the electrical system and the mechanical system

CHAPTER III : DISASSEMBLY
Procedures for disassembling the mechanical system.

CHAPTER IV : TROUBLESHOOTING
Reference values and adjustments, troubleshooting malfunctions, etc.

APPENDICES :PCB CIRCUIT DIAGRAMS, ETC.

Information in this service manual is subject to change due to improvement or re-design of the product. All relevant information in such cases will be supplied in service information bulletins (Technical
Information).

A thorough understanding of this unit, based on information in this service manual and service information bulletins, is required for maintaining its performance and for improving the practical
ability to find the cause of problems.

Download
password : printer1.blogspot.com
BROTHER PRINTER SERVICE MANUAL

BROTHER HL- 1660E LASER PRINTER SERVICE MANUAL

This service manual contains basic information required for after-sales service of the laser printer (hereinafter referred to as ”this machine” or ” the printer”). This information is vital to the service technician in maintaining the high printing quality and performance of the printer.

This service manual consists of the following chapters:

Chapter I : General
Features, specifications, etc.

Chapter II : Theory of Operation
Basic operation of the mechanical system and the electrical system, and their timing.

Chapter III : Electrical System
Theory of the electronics circuit

Chapter IV : Mechanical System
Requirements for a suitable location, disassembling and reassembling procedure of mechanical system.

Chapter V : Maintenance and Servicing
Parts replacement schedule, list of tools, lubricants and cleaners.

Chapter VI : Troubleshooting
Reference values and adjustment, troubleshooting for image defects, troubleshooting for malfunctions, etc.

Appendices : Engine Block Diagram, PCB Circuitry Diagrams, etc.

Information in this service manual is subject to change due to improvement or re-design of the product. All relevant information in such cases will be supplied in service information bulletins (Technical Information).

A thorough understanding of this printer, based on information in this service manual and service information bulletins, is required for maintaining its quality performance and for fostering the practical ability to find the cause of troubles.

Download
password : printer1.blogspot.com
BROTHER PRINTER SERVICE MANUAL